BeO Takes The Heat In RF Transistor Packages

Aug. 14, 2007
Even with challenges from other technologies, beryllium oxide (BeO) remains the insulating material of choice for the most demanding RF power transistor packages.

Power-transistor packaging is not immune to the cost pressures facing commercial RF and microwave markets. RF power-transistor suppliers have long sought alternative materials to traditional insulating materials such as ceramics, including BeO. But the superior characteristics of BeO continue to make it the material of choice at the highest power levels at frequencies up to 4 GHz, especially in demanding military and aerospace pulsed power applications.

BeO is a key insulating material because of its thermal conductivity (TC) of about 285 W/mK at room temperature. Among insulating materials, this TC rivals all but diamond (as high as 1800 W/mK). The nearest competitor to BeO is aluminum nitride (AlN) at about 185 W/mK, with widely used alumina (Al2O3) reaching only 25 W/mK. For applications where thermal management and electrical isolation are critical, it is no wonder that BeO is the primary choice for RF power-transistor packages (Fig. 1).

In addition to thermal conductivity, BeO's thermal coefficient of expansion (TCE) of 6.3 PPM/°C falls between that of silicon (3.3 PPM/°C) and gallium arsenide (5.8 PPM/°C). BeO's TCE is also well matched to other metal matrix composites (MMCs) such as Cu/W, Cu/Mo, and Al/SiC. In other relevant areas, such as electrical resistively and dielectric strength, BeO has better electrical characteristics than AlN and is similar in behavior to alumina. With a low dielectric constant of 6.7 and low loss tangent of 0.0012 at 1 MHz, BeO is also well suited for use at high frequencies. In addition to these characteristics, BeO also is inherently stable in oxidizing environments, in contrast to nitrides such as AlN that tend to decompose over time to their oxide equivalent (see table).

Since beryllia is an oxide ceramic, BeO parts are very stable in oxygen/moisture-containing environments. Ceramic-to-metal joints and metallization coatings are generally very strong and reliable, which is important in the design of high-reliability military systems. In addition, BeO is also about 11 times more resistant to thermal shock than alumina.

Like other ceramic materials, the thermal conductivity of BeO decreases with increases in temperature, in contrast to metals, whose thermal conductivity deteriorates less with increasing temperature. As a result, employing combinations of BeO and metal films has proven very effective for RF power packaging. In the temperature range at which RF power transistors operate, BeO also offers about 30-percent better thermal dissipation than AlN. Even at cryogenic conditions, beryllia remains superior to all other ceramic materials.

The capability of a device or subsystem to rid itself of heat is exceptionally important to product life. For example, the vast majority of failures in base-station electronics are related to thermal issues. Without good package heat dissipation, a device will degrade at an accelerated rate and ultimately fail, and the higher the temperature the sooner this occurs. As a result, device designers consider heat dissipation and thermal management in general an increasingly important concern. Not surprisingly, BeO packaging is very appealing in such dense environments, where even incremental improvements in thermal management can play a major role in extending the operating life of an electronic system.

In applications at higher frequencies, higher current is required near bond interfaces, which necessitates less-resistive interface layers. BeO offers the ability to reduce the area and size of a device while dissipating the same power and reducing capacitance. In small leadless packages, for example, BeO provides an advantage over AlN, which at high frequencies cannot provide the expected electrical or thermal performance that can be achieved when using BeO.

Dielectric constant and dissipation factor are also important parameters in which the characteristics of BeO are desirable. Transmission lines and passive structures are critical components of RF and microwave modules. For many applications, lower dielectric constants are preferred because transmission-line losses are lower and conductor width is increased, which makes circuits more easily produced. Dielectric losses are also reduced with decreasing dielectric constant.

The cutoff frequency of a particular substrate thickness also increases as dielectric constant is lowered for microstrip circuits. As a result, a BeO substrate of a given thickness can be used at frequencies about 20-percent higher than it could with an alumina substrate of the same thickness. Thickfilm lithographically etched, gold-metalized substrates manufactured on BeO exhibit these important characteristics and can operate upwards of 44 GHz. Bonding of copper to BeO enables the conduction of large electrical currents. In addition to conventional metalizing techniques, copper can be applied to BeO via the Direct Bond Copper (DBC) process. DBC on BeO provides conduction paths with lower electrical resistance than thin-film or thickfilm conduction lines. Transistor packages produced via the DBC process perform extremely well through 8 GHz with less than 1 dB of insertion loss.

Several recent developments have further expanded the utility of BeO. Of greatest significance for RF power transistors is a recent increase in thermal conductivity to 325 W/mK achieved by Brush Ceramic Products, (, a division of Brush Wellman, Inc. The enhancement further distances the thermal conductivity of BeO from competing materials, and makes it suited for future RF power devices that deliver greater RF outputs and have correspondingly greater need to dissipate waste heat. The material is currently in beta testing at several customers.

Other enhancements include the ability to produce BeO plates up to 4.5 X 4.5 in., which reduces cost by allowing a greater number of patterns to be created on a single plate. In addition, the new BW1000 substrates from Brush Ceramics increase material strength by up to 25 percent to 38,000 lb./in.2 (262 MPa), achieved by adding proprietary additives while maintaining a purity level of 99.5 percent, and by precisely controlling grain growth and grain distribution during sintering.

With the inherent strengths of BeO, an obvious question is why it is not used exclusively (as it once was) in RF power transistor packaging even though it remains extremely popular in optical, automotive, power supply, and many other areas in which its high TC and other desirable characteristics remain unmatched (Fig. 2). The answer is twofold. First, cost is a major driver of every commercial application of RF and microwave technology, and BeO is more costly than alumina and in some applications can be more costly than AlN. If a device's power dissipation and other performance parameters can be accommodated by AlN or alumina, one of these will likely be the insulating material of choice. In addition, laterally diffused metal-oxide-semiconductor (LDMOS) devices, which do not require die attached to a dielectric, eliminate the need for BeO, and are widely used at frequencies as high as 4 GHz.

Page Title

The other issue concerns the potential health effects of BeO, which have long been inaccurately communicated and often exaggerate the hazards to the end-user. While it is true that fine BeO particulates can cause serious health effects in a small percentage of workers, this risk exists primarily in the ceramics manufacturing area where BeO is handled in powder form. Most BeO is supplied to end customers as a finished part and requires no special handling in a normal assembly environment. With regard to the primary ceramics manufacturing workers, Brush Ceramic Products has long been a world leader in the health and safety of beryllium workers and has taken extraordinary steps to ensure worker safety, which have proven to be very successful. In terms of legal restrictions, BeO is now and will continue to be available worldwide without legislative restriction such as RoHS or WEEE.

While AlN has attractive electrical properties, it requires manufacturing technologies that remain an obstacle to delivering a cost-effective product. For example, AlN powder synthesis and firing requires inert atmospheric conditions in nitrogen gas furnaces and graphite furnaces that can reach +1870°C. AlN powder preparation and sintering is also three to four times more expensive than that of oxide ceramics such as alumina or BeO.

Finally, since AlN is a man-made material and not found in nature, it will always have a limited life, and is not stable in moisture-containing air, especially at higher temperatures. As a result, AlN is not often chosen for use in demanding aerospace and defense applications in which long-term, stable performance in environmentally hostile conditions is essential.

After more than 50 years, BeO packaging technology for microwave and power RF applications remains superior at the highest power levels when the greatest amount of heat is dissipated. The stability of beryllium-oxide ceramic components in reducing and oxidizing environments also makes it the prime candidate for long-life, high-reliability commercial and defense applications. As a thermal-management ceramic, BeO outperforms AlN for pulsed-power RF packaging applications. Finally, BeO properties and metallization technologies have been very consistent over time. So while the onslaught continues from other insulating materials, the use of BeO continues to grow in RF applications that demand its inherent superiority in many key parameters, and will likely continue to do so for many years.

Sponsored Recommendations

Ultra-Low Phase Noise MMIC Amplifier, 6 to 18 GHz

July 12, 2024
Mini-Circuits’ LVA-6183PN+ is a wideband, ultra-low phase noise MMIC amplifier perfect for use with low noise signal sources and in sensitive transceiver chains. This model operates...

Turnkey 1 kW Energy Source & HPA

July 12, 2024
Mini-Circuits’ RFS-2G42G51K0+ is a versatile, new generation amplifier with an integrated signal source, usable in a wide range of industrial, scientific, and medical applications...

SMT Passives to 250W

July 12, 2024
Mini-Circuits’ surface-mount stripline couplers and 90° hybrids cover an operational frequency range of DC to 14.5 GHz. Coupler models feature greater than 2 decades of bandwidth...

Transformers in High-Power SiC FET Applications

June 28, 2024
Discover SiC FETs and the Role of Transformers in High-Voltage Applications